Team:Paris Saclay/Notebook/September/7

Wednesday 7th September

Lab work

Visualization

Gibson of cleaned up PCR products FRB from clone 9 x pSB1C3 - GFP 11 from clone 8

By Maxence

Gibson was performed on cleaned up PCR products FRB from clone 9 (insert) x pSB1C3 - GFP 11 from clone 8 (plasmid) with the following protocol:

For each 20μl of reaction, mix the following reagents :

  • 0.64 µL of insert
  • 3.68 µL of plasmid
  • 5.67 µL of water
  • 10 µL of buffer

Two controls were done: one without insert and one without buffer (water was added in order to have a total of 20 µL. The PCR was performed as follow : 1 hour at 50°C.

Clean-up of Gibson products

By Maxence

Gibson products obtained were cleaned up by using the NucleoSpin Gel and PCR Clean-up kit protocol.

Transformation of DH5a cells with FRB - GFP 11 in PSB1C3 obtained by Gibson

By Maxence

Dh5a cells were transformed with pSB1C3 containing FRB - GFP 11, or containing control (no mix added when Gibson performed) using the usual protocol.

Colony PCR of 16 clones containing dCas9 NM - GFP 10

Maxence

Transformed cells which had been grown overnight were used for colony PCR. For that purpose, 16 clones containing dCas9 NM - GFP 10 obtained by Q5 amplification and 16 clones containing dCas9 NM - GFP 10 obtained by Phusion amplification were screened and used for the usual protocol of Colony PCR. The same colonies were also plated on Petri dish containing solid LB + 30 µg/mL Cm and liquid cultures (LB + 30 µg/mL Cm) were made from these clones. Both petri dishes and liquid cultures were grown at 37°C.





Q5 PCR on dCas9 ST - GFP 11 in pSB1C3, FRB in pJET and GFP 1.9 in pUC19

By Maxence

Q5 PCR was performed on plasmids with the following protocol:

For each 50μl of reaction, mix the following reagents :

  • 1 µL of plasmid
  • 1 µL of dNTPs (10mM)
  • 1 µL of each primer mix (10µM)
  • 10 µL of Q5 buffer (5X)
  • 0,5 µL of Q5 high fidelity polymerase
  • 35,5 µL of nuclease free water

Mix gently and aliquot 50 μl of the mix into the PCR tubes on ice. Perform PCR as follow:

Step Temperature Time
Initial denaturation 98°C 30sec
30 cycles 98°C 10sec
Tm 20sec
72°C t
Final Extension 72°C 2min
Hold 4°C $\infinity\$ 
Primers used were:
Matrix dCas9 ST - GFP 11 in pSB1C3 clones 6 and 8 FRB in pJET clones 4 and 9 GFP 1.9 in pUC19
Primers iPS152 and iPS151 iPS149 and iPS150 iPS84 and iPS140
Tm 57,5°C 56,7°C 72°C
t 1 min 30 20 sec 30 sec


NanoDrop Measurements

By Maxence

Sample Concentration (ng/µL)
PCR fragment GFP 11 clone 6
 187.23
PCR fragment GFP 11 clone 8
 156.85
PCR fragment FRB clone 4
 75.67
PCR fragment FRB clone 9
 246.41
PCR fragment GFP 1.9
 22.06

Gel of cleaned up PCR products

By Maxence

After amplification, 3 µL of each cleaned up PCR products and 5 µL of DNA ladder were placed in wells and migrated at 100V during 30 min.

PCR products expected were :

PCR products Expected band size (bp)
GFP 11- pSB1C3 2500
FRB 374
GFP 1.9 862
Result of the migration

GEL GEL GEL