Difference between revisions of "Team:Exeter/Proof"

Line 596: Line 596:
 
<div class="container">
 
<div class="container">
 
<h1>Proof</h1>
 
<h1>Proof</h1>
 +
<h3>Continuous culture</h3>
 +
 +
<p id="pp">Before starting the project we spoke to Prof. Robert Beardmore EPSRC Leadership Fellow in the Mathematical Biosciences at Exeter University. Much of his research has been into antibiotic resistance. We discussed how high selection pressure is applied by prolonged use of antibiotics and how kill switches may be analogous to this. It is clear that cells which develop a mutation that inactivates the kill switch would be strongly selected for. It was estimated that functional loss of the kill switch would occur in a short amount of time as a result, and if this was the case, could have strong implications for kill switch longevity. To test this we decided to use a ministat to perform a continuous culture. The ministat was developed in the Dunham lab at the University of Washington (Miller <i>et al</i>, 2013). Each ministat chamber is fed from its own media container via a peristaltic pump, with the culture volume set by the height of the effluent needle in the chamber. Air is bubbled through flasks of water to hydrate it and then used to agitate the culture. Chambers were inoculated with freshly transformed <i>E. coli</i> BL21 (DE3) and samples taken to test if the kill switches were still viable. By simulating in miniature how a kill switch might behave in an industrial setting, the ministat provides a proof of concept for how a kill switch might be maintained in larger chemostats during a continuous culture. A protocol for running experiments in the ministat can be found <a href="#MinistatProt">here</a>
 +
</p>
 +
<br>
 +
<br>
 +
 +
<!--These are pictures of the ministat components, could you put them in a row. Container-pump-effluent-->
 +
<div class="col-xs-12" style="margin:0;padding:0;">
 +
<div class="col-xs-12 col-sm-4">
 +
<img style="max-width:100%;" src="https://static.igem.org/mediawiki/2016/4/48/T--Exeter--container.jpg"> <!--Picture of the container is too big-->
 +
<span class="caption">Media container used to feed a single ministat chamber.</span>
 +
</div>
 +
<div class="col-xs-12 col-sm-4">
 +
<img style="max-width:100%;" src="https://static.igem.org/mediawiki/2016/6/6a/T--Exeter--pump.JPG"> 
 +
<span class="caption">Peristaltic pump</span>
 +
<!--Picture of the pump is too big-->
 +
</div>
 +
<div class="col-xs-12 col-sm-4">
 +
<img style="max-width:100%;" src="https://static.igem.org/mediawiki/2016/a/a3/T--Exeter--effluent.JPG"> 
 +
<span class="caption">Ministat chambers in heatblock and 1 litre Duran bottle used to collect effluent</span>
 +
<!--Picture of the effluent bottle is too big-->
 +
</div>
 
 
 +
</div>
 +
<div class="row">
 +
 +
<div class="col-xs-12">
 +
<img style="max-width:100%;padding: 5px 30% 5px 30%;" src="https://static.igem.org/mediawiki/2016/8/8a/T--Exeter--ministat.jpg">
 +
<div class="col-xs-3"></div>
 +
<div class="col-xs-6"><span class="caption" style="padding: 5px 30% 5px 30%;">Ministat running a preliminary experiment to calibrate parameters such as dilution rate and temperature of the heat block. 50 ml burettes used here to accurately measure effluent levels. 1 litre Duran bottles were used for effluent collection in the main experiment due to greater volumes of effluent. </span></div>
 +
<div class="col-xs-3"></div>
 +
</div>
 +
</div>
 +
<p id="pp">Our own growth curve was performed to determine the maximum specific growth rate of <i>E. coli </i> BL21 (DE3) in our lab, but could not be conducted for a sufficient length of time to be accurate. A maximum specific growth rate value of 1.730 was used (Cox, 2004). The ministat must be set to a flow rate at which dilution rate is less than maximum specific growth rate. This prevents the culture being washed out of the growth chambers. The dilution rate of the culture was calculated by measuring flow rate at a setting of 7.5 rpm on the peristaltic pump. For practical reasons the pump could not be run faster than this due to the amount of media needed. The dilution rate was set at 0.2 which produced cultures that grew at an average OD of 3.47 for KillerRed samples, 3.64 for KillerOrange samples and 3.17 for lysozyme samples. The ministat must be set to flow rate at which dilution rate is below the maximum specific growth rate. This prevents the culture being washed out of the chamber. OD was measured daily with a Bug Lab OD scanner. When the same sample was measured in a tecan infinite 200 pro plate reader the Bug Lab showed reading approximately three times higher. The difference between the samples was consistent regardless of the method used to measure OD.
 +
</p>
 +
 
</div>
 
</div>
  

Revision as of 12:36, 13 October 2016