Difference between revisions of "Team:UofC Calgary/Design"
Syedjafri97 (Talk | contribs) |
Syedjafri97 (Talk | contribs) |
||
| Line 266: | Line 266: | ||
<p>To ensure the durability of our patch during accidents such as punctures, tears, or the patch falling off the user, we researched materials used for transdermal delivery. Companies specializing in transdermal delivery were contacted for design, material, and manufacturing advice. We designed small-scale prototypes using SOLIDWORKS, and printed them in 3D to better understand the patch to scale. Finally, we prototyped our design using the researched materials. These materials were also tested in our laboratory for their ability to allow mBBI to diffuse through while retaining bacterial cells. To determine if our design was cost effective, we also looked into large-scale manufacture and the level of difficulty to manufacture multiple patches. This led us to develop a user’s manual for our patch and project design, where all information related to our applied design can be found. This user manual can be found below.</p><br> | <p>To ensure the durability of our patch during accidents such as punctures, tears, or the patch falling off the user, we researched materials used for transdermal delivery. Companies specializing in transdermal delivery were contacted for design, material, and manufacturing advice. We designed small-scale prototypes using SOLIDWORKS, and printed them in 3D to better understand the patch to scale. Finally, we prototyped our design using the researched materials. These materials were also tested in our laboratory for their ability to allow mBBI to diffuse through while retaining bacterial cells. To determine if our design was cost effective, we also looked into large-scale manufacture and the level of difficulty to manufacture multiple patches. This led us to develop a user’s manual for our patch and project design, where all information related to our applied design can be found. This user manual can be found below.</p><br> | ||
| − | + | <center><div id="empty"></div></center> | |
| − | <!-- End--> <center><object data=" | + | <!-- End--> <center id="pdf"> <object data="https://static.igem.org/mediawiki/2016/2/26/T--UofC_Calgary--Applied_Design.pdf" type="application/pdf" width="100%" height="600px"> |
Your device does not support embed PDFs. Please click the following link to open up the PDF. <a href="https://static.igem.org/mediawiki/2016/2/26/T--UofC_Calgary--Applied_Design.pdf">Applied_Design.pdf</a> | Your device does not support embed PDFs. Please click the following link to open up the PDF. <a href="https://static.igem.org/mediawiki/2016/2/26/T--UofC_Calgary--Applied_Design.pdf">Applied_Design.pdf</a> | ||
| − | </object> </center> | + | </object></center> |
</div> | </div> | ||
| Line 459: | Line 459: | ||
}); | }); | ||
}); | }); | ||
| + | </script> | ||
| + | <script> | ||
| + | IS_IPAD = navigator.userAgent.match(/iPad/i) != null; IS_IPHONE = (navigator.userAgent.match(/iPhone/i) != null) || (navigator.userAgent.match(/iPod/i) != null); if (IS_IPAD) { IS_IPHONE = false; } | ||
| + | |||
| + | if(IS_IPAD || IS_IPHONE){ | ||
| + | document.getElementById("pdf").remove(); | ||
| + | |||
| + | var img11=document.createElement("a"); | ||
| + | img11.href='https://static.igem.org/mediawiki/2016/2/26/T--UofC_Calgary--Applied_Design.pdf'; | ||
| + | img11.innerHTML = 'View PDF'; | ||
| + | |||
| + | document.getElementById("empty").appendChild(img11); | ||
| + | |||
| + | } | ||
| + | |||
| + | |||
</script> | </script> | ||
</body> | </body> | ||
</html> | </html> | ||
Revision as of 08:30, 19 October 2016
Applied Design
Through conversations with our targeted audience of astronauts, we learned there exists a challenging engineering problem of shielding astronauts from ionizing radiation. Current proposed solutions such as coating spaceships in lead, using carbon nanotubes filled with boron, or using nuclear reactors to generate radioprotective magnetic field are too expensive due to the cost of rocket fuel during launch and transport to deep space. Our delivery system allows astronauts to be shielded against ionizing radiation, which is currently a large factor preventing longer space flights.
In order to the develop a sophisticated solution for the administration of our radioprotective peptide mBBI, a biotherapeutic transdermal patch was considered. Through simulations, mBBI has a half-life of four hours. A typical mode of administration, such as intravenous injections or oral administration, would have been ineffective at maintaining a constant dose of peptide, as the peptide would be degraded by the body. After a period of time, mBBI would have to be readministered to maintain an effective dosage concentration, resembling a sinusoidal wave in drug administration. Our transdermal patch design allows us to maintain a stable concentration of mBBI in the blood. The peptide is constantly produced inside the patch by Bacillus subtilis and continuously delivered into the body via diffusion. In addition, the application procedure is noninvasive.
To better integrate our project into existing infrastructure and for future space missions, we designed our delivery system for long-term use and portability. Our patch design included four small pockets attached to one main large pocket. One pocket of the patch contains dry B. subtilis endospores. When pressure is applied, the spores will be rehydrated and activated to their vegetative state. This allows our patch to be stored for long periods of time via desiccation when not in use. To extend the lifetime of the bacteria in the patch, the other three pockets include super-rich media, which can be added when the initial nutrients are depleted. This will help extend the lifetime of individual patches, reduce the total number of patches needed for a mission and reducing overall waste.
To ensure the durability of our patch during accidents such as punctures, tears, or the patch falling off the user, we researched materials used for transdermal delivery. Companies specializing in transdermal delivery were contacted for design, material, and manufacturing advice. We designed small-scale prototypes using SOLIDWORKS, and printed them in 3D to better understand the patch to scale. Finally, we prototyped our design using the researched materials. These materials were also tested in our laboratory for their ability to allow mBBI to diffuse through while retaining bacterial cells. To determine if our design was cost effective, we also looked into large-scale manufacture and the level of difficulty to manufacture multiple patches. This led us to develop a user’s manual for our patch and project design, where all information related to our applied design can be found. This user manual can be found below.
