Difference between revisions of "Team:Paris Bettencourt/Notebook/Protocols"

Notebook

Protocols

Bibliography

Phage Display Protocols

Phage Titering

The number of plaques will increase linearly with added phage only when the multiplicity of infection (MOI) is much less than 1 (i.e., cells are in considerable excess). For this reason, it is recommended that phage stocks be titered by diluting prior to infection, rather than by diluting cells infected at a high MOI. Plating at low MOI will also ensure that each plaque contains only one DNA sequence.

1. Inoculate 10mL of LB with ER2738 from a plate and incubate with shaking ~3-4 hours (mid-log phase, OD600 ~ 0.5).
2. While cells are growing, melt Top Agar in microwave and dispense 3 ml into sterile culture tubes, one per expected phage dilution. Maintain tubes at 45°C.
3. Pre-warm, for at least one hour, one LB/IPTG/Xgal plate per expected dilu¬tion at 37°C until ready for use.
4. Prepare 10 to 103 -fold serial dilutions of phage in LB; 1 ml final volumes are convenient. Suggested dilution ranges: for amplified phage culture supernatants, 10^8 – 10^11; for unamplified panning eluates, 10^1–10^4. Use aerosol-resistant pipette tips to prevent cross-contamination, and use a fresh pipette tip for each dilution.
5. When the culture in Step 1 reaches mid-log phase, dispense 200 μl into microfuge tubes, one for each phage dilution.
6. To carry out infection, add 10 μl of each phage dilution to each tube, vortex quickly, and incubate at room temperature for 1–5 minutes.
7. Transfer the infected cells one infection at a time to culture tubes containing 45°C Top Agar. Vortex briefly and IMMEDIATELY pour culture onto a pre-warmed LB/IPTG/Xgal plate (200µM IPTG, 30µg/mL X-gal). Gently tilt and rotate plate to spread top agar evenly.
8. Allow the plates to cool for 5 minutes, invert, and incubate overnight at 37°C.
9. Count plaques on plates that have approximately 100 plaques. Multiply each number by the dilution factor for that plate to get phage titer in plaque forming units (pfu) per 10µL. Multiply by 100 to get the pfu/mL.

Panning procedure

DAY 0

• Streak ER2738 from glycerol stock on LB+Tet plate.
• Incubate overnight at 4°C the piece of fabric/thread with 1mL of blocking buffer. Alternatively, after inoculation of the titering culture incubate the piece of fabric/thread at least 1 hour at 4°C on DAY 1.

DAY 1

1. Inoculate 10 ml of LB+Tet medium with ER2738 in a 125mL Erlenmeyer flask. This culture will be used for titering in Step 8 and can be used in ~3.5 - 4 hours. Incubate at 37°C with vigorous shaking. Incubate the titering culture until needed.
2. Remove the piece of fabric/thread from the blocking solution. Wash the fabric rapidly 10 times with TBST 0.1% (TBS + 0.1% [v/v] Tween-20) by dipping the threads in a well from a six-well plate filled with ~8mL TBST per well and going back and forth through the washing solution. Alternatively beackers can be used in place of six well plate.
3. Dilute a 25-fold representation of the library (e.g., 2 x 10 11 phage for a library with 2 x 10 9 clones) with 250µl of TBST (therefore add 10µL of phage library). Place the piece of fabric/thread in the Eppendorf tube containing the library and rock gently for 60 minutes at room temperature.
4. Inoculate 20mL of LB medium in a 250mL Erlenmeyer flask just before the end of the incubation period of the fabric in the phage library solution. Incubate at 37°C with vigorous shaking. This culture will be used to amplify the eluted phages.
5. Remove piece of fabric/thread from the Eppendorf tube.
6. Wash fabric 20 times with TBST as in step 2.
7. Elute bound phage with 1 ml of an ap¬propriate elution buffer for the interaction being studied. A general buffer for nonspecific disruption of binding interactions is 0.2 M Glycine-HCl (pH 2.2), 1 mg/ml BSA. Rock gently for 15 minutes. Discard the piece of fabric. Neutralize supernatant with 150 μl of 1 M Tris-HCl, pH 9.1.
8. Titer a small amount (~2 μl) of the eluate as described in the Phage Titering protocol. Plaques from the first or second round eluate titering can be sequenced if desired.
9. Amplify the rest of the eluate by adding the eluate to the 20-ml ER2738 culture from Step 4 (should be early-log at this point, i.e. OD600 ~ 0.01-0.05) and incubating with vigorous shaking for 4.5 hours at 37°C.
Note: The remaining eluate can be stored overnight at 4°C at this point, if preferred, and amplified the next day. In this case, inoculate 10 ml of LB+Tet with ER2738 and incubate with shaking overnight at 37°C. The next day, dilute the overnight culture 1:100 in 20 ml of LB in a 250-ml Erlenmeyer flask (do not use a 50 ml conical tube) and add the unamplified eluate. Incubate with vigorous shaking for 4.5 hours at 37°C and proceed to Step 10.
10. Transfer the culture to a centrifuge tube and spin for 10 minutes at 12,000 g at 4°C. Transfer the supernatant to a fresh tube and re-spin (discard the pellet).
11. Transfer the upper 80% of the supernatant to a fresh tube and add to it 1/6 volume of 20% PEG/2.5 M NaCl. Allow the phage to precipitate at 4°C for at least 2 hours, preferably overnight.

DAY 2

DAY 3

DAY 4

DAY 5