Team:Sheffield/project/device/final
|
HEADING |
|
|---|
|
|
|
|
||||
|---|---|---|---|---|---|---|---|
|
|
|
|
|
Introduction
Our device went through several changes throughout the project which can be seen elsewhere on our site [link]. This section will cover the final operation and workings of the device. The device houses the diagnostic capsule or needs. The device has been designed to be used in a GP’s office with minimal interaction; doctors will be busy and can’t spend all their time watching the device. Our goal with the device is to meet the specifications set out by the experts we interviewed which is what we believe we have created with the design and prototype. It is suggested to read the biological operation of the device first. [link to final description of biology steps]
The page has been split into two sections as there are two main components of the device:
- Capsule – The capsule covers the three biological stages of the operation where the reagents react. This is the replaceable part of the device which needs a new capsule for each test.
- Chamber – The measurement stage of the device where the GFP levels are measured and quantified to give the result. This part of the device can be used unlimited times.
Design
The capsule contains all the reagents for the three biological reactions (covered in the biology section), housed within an inner and outer tube [figure 1]. The inner tube contains our engineered machine, the modified E.coli , and the outer tube contains the siderophores and iron. At one end of the capsule is a simple one-way valve which liquids can be injected into. The tube would be designed and manufactured like a glow stick with the outer-tube being very flexible and the inner tube being brittleHence, when bent, the inner tube would break and spill its contents. The capsule is a one use item; it has been designed to be kept affordable for each test.
Figure 1 - The Capsule design
Operation
The operation of the capsule follows [figure 2]:
- Take a blood sample from the patient. Inject the blood with a syringe through the one-way valve. [figure 2a]
- The blood sample mixes with the siderophores and iron in the chamber. Shake the tube for around a minute which should give the lipocalin in the blood plenty of time to mix. If Lipocalin is present it binds to the siderephore-iron complexes The one-way valve will keep everything contained and in the tube. [figure 2b]
- Break the inner tube. This can be done by simply bending the tube which will break the inner tube containing the E.coli . This allows the lipocalin with the bound siderephores and iron to interact and any siderophore-iron complexes not bound to Lipocalin will be taken up by the E. coli.
- Give another shake for good measure before it is ready to be placed into the measurement chamber.
Figure 2 - Images showing the operation of the capsule
Design
This is the second part of the device. This is a much larger device that houses all the measurement electronics and the stand for the capsule. The schematic design can be seen below in [figure 3a+b] . On the right is the measurement chamber. This is where the capsule would sit in a darkened chamber which allows for the optimal conditions to measure any levels of GFP fluorescence. On the left are the electronics. This mainly consists of a micro-processing board. In reference to [figure 3], the parts of the measurement chamber are:
- Arduino board – this is a micro-processor mounted onto a board that can take in and send out electronic signals. This will take in the data from the measurements from the sensors to decide if the GFP levels are high enough or not for a bacterial infection.
- Capsule mount – where the capsule would sit in the measurement chamber
- Back mounted LED’s – two LED’s sit under the mount to activate the GFP and RFP. The GFP LED emits at 400nm and the RFP LED emits at 570nm.
- Light dependent resisters – electronic components that change resistance based on light levels received.
- Coloured filters – these sit by the LDR’s and remove any light that isn’t emitted from the GFP or the RFP to get the best readings.
Figure 3 - Left:basic schematic of front view of the chamber, Right: basic schematic of top view of chamber
Operation
The operation of the device follows [figure 4]:
