Team:Ionis Paris/05 09 16
Our goal is to remove a mutation of one base which was revealed by sequencing of BB12 and BB123 (the biosensor). This mutation is situated in the start codon of the XylR gene. We need to change a G for a T: AGG —> ATG. The principle of site-directed-mutagenesis (SDM) is to remove a mutation with primers that contain the good base in the middle of its DNA sequence. Those primers are called “back-to-back primers”. Preview of the BB123 sequencing that revealed the start codon mutation in the XylR gene: BB12-4 (from miniprep 29/07) BB123-6 (from miniprep 04/08) Primers: SDM-F (forward) and SDM-R (reverse) —> Ta = 57°C 1. Mix for 2 samples (Total volume Mix : 48 µL) in an Eppendorf tube : 18 µL H2O 2.5 µL Primer SDM-F ( 0.5 µM final) 2.5 µL Primer SDM-R (0.5 µM final) 25 µL Q5 Hot start high-fidelity 2X Master Mix (1 X final, NEB #E0552S) 2. Add in PCR tube in the respected order: 24 µL Mix 1 µL of DNA fragment (BB12 & BB123) Gently mix the reaction and spin down microcentrifuge 3. Set the following parameters for the PCR reaction : BB12 (4272 bp): BB123 (5377 pb): 1. In PCR tube, adding in the respected order (bigger volume first and enzyme last): 5 µL 2X KLD Reaction Buffer (1X final, NEB #E0552S) 3 µL Nuclease-free H2O 1 µL PCR product (BB12 / BB123) 1 µL 10X KLD Enzyme Mix (1X final, NEB #E0552S) 2. Incubation 5 min at room temperature The objective is to transforme competent DH5⍺ cells with the SDM products BB12mut and BB123mut. 2 aliquots of DH5⍺ Competent cells (from the 23/07/16) Plasmid DNA : KLD mix with SDM products BB12mut and BB123mut Petri dish LB+Cm: Cm concentration = 25 µg/mL Expected results / Obtained results: We need 6 LB+Cm plates + 4 LB plates Thaw tubes of DH5⍺ competent cells on ice for 10 min. Mix gently and carefully pipette 50 µL of cells into the 4 transformation tubes on ice. Add 5 µL of the KLD mix to the cell mixture./p> Carefully flick the tubes 4-5 times to mix cells and DNA. Do not vortex./p> Place on ice for 30 min. Do not mix./p> Heat shock at exactly 42°C for 45 s. Do not mix./p> Place on ice for 5 min. Do not mix./p> Pipette 250 µL of room temperature SOC into the mixture./p> Place at 37°C for 1h at 250 rpm./p> Warm selection plates to 25°C./p> Mix the cells thoroughly by flicking the tubes and inverting./p> Spread the corresponding volume onto each plate./p> Incubate all the plates O/N at 37°C./p> Some colonies on the petri dishes LB+Cm plated with 50 µL of bacteria transformed with the different ligation products and more on the petri dishes LB+Cm plated with 200 µL of bacteria. We obtain the expected results. The transformation worked. Colonies contain a plasmid with the Chloramphenicol resistance gene, present in pSB1C3. However, it is possible that the PCR of the SDM do not work properly, that it only amplified a section containing the resistance chloramphenicol coding device. A PCR colonie is necessary to check the size of the plasmid present in colonies, and therefore to ensure that bacteria incorpore the correct plasmid BB12mut / BB123mut.
Site Directed Mutagenesis: on BB12 and BB13
Objectives
At the end of the SDM we will get the correct BB12 and BB123 (biosensor) biobricks with the ATG in the XylR gene. It will be named BB12mut and BB123mut.
Materials
Protocol
PCR
Lid temperature: 98°C
Initial denaturation: 98°C, 30 s
30 cycles of: 98°C, 10 s
57°C, 30 s
72°C, 2 min 8 s
Final extension: 72°C, 2 min
Hold: 4°C
Lid temperature: 98°C
Initial denaturation: 98°C, 30 s
30 cycles of: 98°C, 10 s
57°C, 30 s
72°C, 2 min 41 s
Final extension: 72°C, 2 min
Hold: 4°CKinase, Ligase & DpnI (KLD) Treatment:
Transformation: competent DH5⍺ cells with SDM products BB12mut and BB123mut
Objective
Materials
Protocol
Experimental conditions realized :
Transformations protocol:
Results (obtain the 06/09)
Expected results :
A bacterial lawn on the LB petri dishes without antibiotic.
No colonies on the LB+Cm petri dish plated with bacteria transformed with no plasmid (- control).Obtained results:
Interpretation
