Team:CGU Taiwan/Safety

Leijuvant


Safety


(1) Short introduction of our project
Transgenic Leishmania that can be inactivated by light exposure acts as a safe carrier to deliver specific antigens to the APCs for T cells and humoral response. Based on this concept, we established a new model system to generate antigen-specific inactive Leishmania adjuvant (Leijuvant).


(2) What organisms do we use?
Leishmania, DC2.4, E.coli(DH5α, BL21), C57BL/6 mice


(3) Which part do we use?
Full length of HA and OVA: We used full length sequence of hemagglutinin (HA) of H1N1 and Ovalbumin as our testing antigen that is expressed in Leishmania.
5’UTR, 3’UTR, 2.3kb intron: the sequence is originally from Leishmania genome. Act as promotor, terminator, and expression modulating part in our device.


(4) Where do we perform the experiments?
Leishmania and DC2.4 culturing and experiments will be performed in a BSL-2 lab within the flow hood in an independent room and requires wearing lab gloves. Once the Leishmania is inactivated it can be manipulated on the open bench. DH5α and BL21 are manipulated in the Laminar flow. Normal experiments are performed on open bench with gloves.


(5) The training of the lab team
We received lecture of the following topics: registration for the use of biological materials, human pathogens, recombinant DNA experiments, potentially infectious materials, animals handling, the use of biological safety cabinets (BSCs) and other laminar flow benches (LFBs), emergency procedures for incidents, biosafety levels signs and labels, etc. We further received laboratory practices training of biosafety level 1 and 2. All the experiments are under Dr. Yu and Dr. Chang’s instructions.


(6) How do we protect us?
Follow the requirements from different biosafety level laboratory strictly, including wearing gloves, lab coats, masks and goggles if required.


(7) Safety concern in our project
Leishmania is a genus of trypanosomes that are responsible for the disease leishmaniasis, a blood-borne disease that is spread by sandflies. Leishmania culturing and experiments will be performed in a BSL-2 lab within the flow hood in an independent room and requires wearing lab gloves. There is almost no chance of infecting people under this experimental condition since there is no direct contact with Leishmania. Also, Leishmania will not be able to survive once it leaves the culture condition. Once it is photo-inactivated it can be manipulated on the open bench.


(8) How to verify the safety of leishmania after photo-inactivation
1. How to conduct the photo-inactivation?
Photosensitizers (PS) can be delivered endogenously with delta-aminolevulinate (ALA) and exogenously with phthalocyanines (PC). Detailed protocol (link)
With loading ALA, we can see the florescence with the excitation of uroporphyrin in the 12-well tissue culture plate during illumination of long-wave UV lamp (365nm)1(Fig. 1A.). There wasn’t any illumination by UV lamp without loading ALA(Fig. 1B.). After illuminating with long-wave UV , After long-wave UV illumination, we then put it under the LED red light with the wavelength of 620~630nm for 10 minutes (Fig. 1C.) and the double photo inactivation is complete.


2. How to confirm the sucess of photo-inactivation?
     According to (Chang, K. P., et al. 2016.)2we can use the following method to confirm the safety of photo-inactivated Leishmania.
(I) Microscopy of flagellar motility
After illuminating by long-wave UV and red light, you can observe the samples under the microscope. The difference between [+drug, +light]; [+drug, -light]; [-drug;-light] groups can be easily seen. With the illumination of the both chemicals, all six wells of one plate show no flagellar motility under 100x magnification. However, the control group, [+drug, -light] and [-drug;-light], have high motility same as the wild-type Leishmania.
(II) Cultivation for growth (2 weeks)
To further confirm the complete inactivation of Leishmania, we separated 100μl from each sample, [+drug, +light], [+drug, -light] and [-drug;-light], right after illumination. And add them into 24-Well plate containing M199+10%HI-FB medium. Observed and kept tract of it continuously for two weeks. Except the [+drug, +light] group, the other two groups were moving and increasing normally. As for the [+drug, +light] group, there was no motility, or proliferation of the Leishmania from the beginning to the end of the two weeks.
(III) 2 months after subcutaneously injecting inactivated Leishmania into mice
We subcutaneously injected mouse with108 of photo-inactivated Leishmania on both sides of the back around the shoulders, and injected normal saline as the control group. There was no skin ulcers or inflammation and no any other Leishmaniasis symptoms among the 10 mouse that serve as our experimental group(Fig. 2.).


(9) The product safety concern in the future
Environmental concern
Leishmania culture requires a certain osmolarity and combination of nutrients. Therefore, our transgenic Leishmania will not survive as soon as it leaves the medium.
Side effects of adjuvant
There are some potential adverse effects underlying every drug and vaccine. More animal test should be carried out and the most efficient dose in human will be selected before clinical trials. In the clinical study, side effect after immunization will be identified and study design will be modified as well. If our product passes the FDA approval, the report of unexpected effect will be always under inspection.


(10) How would your project be used in the real world?
Our Leijuvant can act to facilitate both humeral and cellular immune response which may contribute to the development of vaccine nowadays. Combined with our prediction software, the platform can predict the peptides on MHC molecules and help to optimize the peptide presentation which may benefit to engineer the sequence for further research and developing a more efficient vaccine.