Enzyme Assays

In order to guarantee the efficiency of our own secreted enzymes and find optimum environment in our project set up for the own enzymes and bought ones, a functional enzyme assay is necessary.

Introduction

The aim of the enzyme assays, is to determine the amount of enzymes present in the sample under certain conditions, making activity comparable between the samples and experiments. The activity is described by the product formed over the given time or how much substrate has been used up.

Different parameters affecting the activity of an enzymes are substrates and their concentration, pH, ionic strength, buffer type and temperature.

In our project, method of stopped colorimetric assays was used. This means that the assay was stopped after a fixed time with the use of temperature and the amount of product formed was measured. Colorimetric assay makes it possible to to quantify the product of interest with the use of spectrophotometer, by reacting it with another reagent. The measured absorbance is directly proportional to the product in the sample. In this experiment, 3,5-Dinitrosalicylic acid was used.

The enzymes tested were endoglucanase (endo-1,4-β-D-glucanase, Acidothermus cellulolyticus, Sigma-Aldrich) and xylanase (endo-1,4-β-Xylanase M4, Aspergillus niger, Megazyme). First enzyme belongs to cellalases and breaks down cellulose molecule by hydrolysis of the 1,4-beta-D- glycosidic linkages into monosaccahrides such as beta-glucose. Xylanase breaks down hemicellulose by degrading polysaccahride beta-1,4-xylan (Beechwood) into xylose.

Experimental Set Up an Validation

The tests done always follow similar recipe (see protocol) that containing sugar or enzyme solution, citrate buffer, water, substrate and DNS. Buffers are needed to adjust and stabilize the pH for enzyme assays. The concentration that works for our chosen enzymes is 50mM. Substrate used for endoglucanase was Carboxymethyl cellulose (CMC) which is a cellulose derivative that the enzyme is able to cleave. Initially for the standard calibrations 1:3 CMC was used but in order to increase the availability of the substrate, the assays with enzymes had CMC 3:7. Substrate for xylanase was 1% xylan, also known as beechwood. DNS is aromatic compound that reacts with reducing sugars to form 3-amino-5-nitrosalicylic acid-

iGEM

This absorbs light at 540 nm creating a possibility to quantify the product present in the sample. Additionally, absorbance at 750 nm was measured in order to subtract the background absorbance for normalization.
Additional water served purpose for having room to change different part of the recipe while still keeping constant volume.
Analysis of the data was done with Open Office Calc.

Standard Calibration

In order to determine the concentration of the substance of interest, standard calibration of the sample with known concentrations is necessary. Xylose was used for xylanase and glucose for endoglucanase.

Initially, a wide range of sugar concentration was tested which was 100 mg/ml to 0,001 mg/ml. Through several experiments, a linear working range was determined to be 10 mg/ml to 0,5 mg/ml (0,1to 0,005 μg in total in the sample)
Experiments creating a linear standard calibration lead to following results.

Figure 1. Glucose standard calibration. The graph shows the absorbance results against the glucose concentrations of 0 to 0,1 μg in total.

Figure 2. Xylose standard calibration. The graph illustrates the relationship between absorbance and xylose concentrations at 0 to 0,2 0,1 μg in total.

Discussion

The final results show linear range as expected and needed in order to validate the complete assay. Deviations increase with increasing concentration as smaller mistakes have then more effect. However, both xylose and glucose yielded usable results that aided in determination of the unit range, that should be used in experiments with enzymes.

Citrate and Glycerol Tests

In order to validate that the read out is not falsified by the variables in the test tube, a series of experiments were done. This entailed doing experiments with citrate buffer and glycerol. Buffer is needed to to create pH optimum and glycerol is enzyme stabilizing agent. Different concentrations of citrate buffer, glycerol and sugars were used.

A range of sugar concentrations of 0,1 μg to 0,0005 μg of total amount of sugar in sample was chosen for both experiments with exception of glucose citrate assay. The reason for higher high end glucose concentration, is due the fact that, results above 0,1 μg went over the measurable absorbance for other experiments and data point could not have been included. For citrate buffer, the concentrations were 1M to 0 M. In case of glycerol, the range was 90-0 %. The experimental set up followed same principle as before. The results can be viewed below.

Figure 3. Citrate Assay with Glucose. Citrate concentrations go from 1 M down to 0 M and were tested with glucose concentrations 1 to 0,0005 μg.

Figure 4. Citrate Assay with Xylose. Citrate buffer of 1 – 0 M tested with xylose concentrations of 0,1 μg to 0,005 μg.

The obtained results show that the absorbance measured at was nearly constant for both, citrate buffer assays with very low fluctuation.

Figure 5. Glycerol Assay with Glucose. The tested glycerol concentration ranged from 90% to 0 and the sugar from 0,1 μg to 0,005.

Figure 6. Glycerol Assay with Xylose. The glycerol concentration varied from 90% to 0 and the sugar from 0,1 μg to 0,005 μg.

The results are similar to the ones from citrate. Here once again the absorbance values stay near constant through all measurements.

Discussion

Citrate and glycerol result showed both similar pattern. There was some fluctuation between the samples, however, this can be taken as an error. Glycerol is rather viscous and therefore, difficult to pipette. Furthermore, sources of mistakes must be considered such as errors from pipetting. All in all, it can be concluded that citrate and glycerol have no effect in the experiments done.

Enzyme Assays

The assays done with xylanase and endoglucanase followed similar principle to the previous experiments. Precautions were taken to keep samples on cooler rack while preparing enzyme samples, in order to preserve the enzyme activity.

Endoglucanase Assays

Endoglucanase assays are made difficult by the substrate viscosity. This is the main source of deviations in these assays. Standard calibration was done in parallel to the enzyme experiments.

The results of the endoglucanase assays are illustrated on the upcoming graphs.

Figure 7. Standard calibration of the Glucose for Endoglucanase. Absorbance is put against the glucose concentrations in μmol.

Figure 8. Endoglucanase Assay. Absorbance of the samples shown in relationship to corresponding enzyme Units.

The graphs show linear ranges but error bars can be considered big. This is especially true for the enzyme experiment. Units used went up to 0,25 U and absorbance maxima was 0,225. Going over the amount of enzymes produced saturated curve. Lower values also showed results that can not be take into account, as they showed random results opposed to constant increase with increasing concentrations.

Xylanase Assay

Xylanase assays were successful and the results can be seen on the graphs below. Standards were done in parallel to the enzyme assay.