Overview
To understand the insect test in an easy way, the testee selection, and experiment design would be briefly described. The results consist of three parts-feeding assay pre-test, the fusion protein improvement test, and preference test.
**Note: The word “Pantide” in the following paragraph refers to the collection of all the toxin design in our project.
Testee selection
In the test of Pantide toxicity, we chose tobacco cutworm as the testee for the insect appetite tests because all the Pantide targets lepidopterans. We hope that we can observe the difference of the three toxins in vivo. Tobacco cutworms, which are one of the major pests in vegetable farms, impact on Crucifers in farmland around the world. In the serious pest damage, the density of tobacco cutworms is approximately up to two hundred million per ha[1]. Therefore, we used five tobacco cutworms to mimic the much more severe situation in our insect experiment.
Experiment Design
All the experiments were to check the functions of Pantide for leaf protection, so the observation of the results would focus on the remained area of the leaf disks.
In the following experiments, we used E. coli BL21 Rosetta-Gami strain to produce Pantide. We aimed to evaluate the remained leaf area applying Pantide. In this insect test, Pantide was diluted into three concentrations to observe the trends of dose response and to confirm the quality of PANTIDE. All the following experiments have three dilution ratios including 1/125 x, 1/25x and 1/5x. Three repeated tests were done in each experiment. See the procedure of insect experiment on Protocols.
Hypothesis
According to the mechanism of Pantide, Pantide is supposed to perform its toxicity in the nervous system of the larvae. We might see larvae paralyze and finally die. So that we may define Pantide as a biological pesticide.
Insect Test Result
Feeding Assay Pre-test
To know the qualitative dose response of Pantide, we prepared the samples with the sonicated LB solution containing Pantide-expressed E. coli Rosetta gami strain and diluted it with the three concentration. This experiment is the pre-test that shows us whether the amount of Pantide is sufficient enough to perform the toxicity against the larvae. We applied the sample onto the leaf disks and put five cutworms into the separate cabinets for feeding assays. The positive control in the experiment was to apply Bacillus thuringiensis, which is the most widely-used bioinsecticide. We preserved all the result of the remained leaves sealing with the glass paper and calculated the percentage of the remained area on the leaves. Here are the feeding assay results.
Figure 1. Remained leaf disks in the pre-test with the Hv1a and Hv1a-lectin.
Figure 2. The analysis of remained leaf area in the pre-test with the Hv1a and Hv1a-lectin.
Figure 1. shows the pictures of the remained leaf disks after twelve hours of feeding assays. After we had done the feeding assays on tobacco cutworms with the three dilution ratio, we measured the area with the software imageJ. Figure 2. shows the percentage of the average remained area on the leaf disks. The higher the bar is, the larger the remained leaves area is. The observed phenomenon can be analyzed below.
With the leaves applying E. coli for a negative control, the remained leaves area with Pantide were all more than that of E. coli. It shows that the sonicated LB solution containing Hv1a/Hv1a-lectin(see the SDS-PAGE) decreases the appetite of tobacco cutworm.
With the dilution of Hv1a/Hv1a-lectin, the remained leaves area decreased, which clearly shows the dose response.
Compared Hv1a with Hv1a-lectin, the remained leaves area in the Hv1a-lectin is higher than that of Hv1a, which means the repellent efficiency of Hv1a-lectin is higher than that of Hv1a.
Compared with the positive control, we can observe that the repellent efficiency of PANTIDE is equal or even higher than it. This shows the efficiency of Hv1a as well.
To sum up, the Hv1a and Hv1a-lectin work well in vivo. The effect can be roughly ranked as:
Hv1a-lectin > Hv1a > E. coli > Negative control
