Team:Cambridge-JIC/Demonstrate
DEMONSTRATION
Hardware: Firing The Gene Gun
We wanted to check the validity of the gun’s design by testing if it could generate pressure pulses which would penetrate a plant cell wall. This was done using onion epidermal tissue, as the tissue layers are only one cell thick so would be the easiest to observe any penetration on microscope imaging.
For bombardment, we prepared the macrocarriers as described in the gun assembly protocol, steps 14-15. We then used simple agar TAP plates we had spare in the lab (approximately 1cm thick), and cut 2x1cm strips of brown onion epidermis to place on the plates.
We then pipetted 150mg of M10 tungsten microparticles, prepared according to our wetlab biolistics protocol, onto each macrocarrier. A fresh 16g CO2 cartridge lasted for around 20 bombardments, ranging from 130-155 psi (though the efficiency of this improved significantly once we became more experienced at pressurising the gun and wasted less CO2).
On inspecting the bombarded onion samples under the microscope, we found evidence of holes in the onion tissue. This suggests these pressures could be suitable for biolistics on plant cells, as the tungsten microparticles were capable of penetrating plant cell walls so should penetrate cells for biolistic transformation.
Our next step in developing the gene gun would be experiment with lower pressures, to find the most efficient pressure pulse for penetration of cells. In the future, we also aim to prove the gun’s use in carrying out chloroplast transformations, by attempting transformation of chlamydomonas samples.
Wetlab
Having developed the parts library for Chlamydomonas reinhardtii and proved the concept of the biobricks standard syntax which allows for the regulated assembly into composite devices we investigating putting this under trial of real-life conditions to transform Chlamydomonas reinhardtii chloroplasts through biolistics. Please read more about the demonstration of the DIY biolistic gene gun we have developed in the lab this summer. Taking advantage of the aadA resistance gene which we were able to verify in E. coli colonies, we constructed this Phytobrick with a 5’ UTR psaA promoter and a rbcL 3’ UTR terminator, each flanked by the homology regions for insertion into the trnE2-psbH intergenic region (shown to yield high expression rates of the transgene).
As a side note, biolistics is a complex transformation process which requires a high precision in template preparation and sterility conditions. Our team, due to the time constraints of working with Chlamydomonas reinhardtii, were only able to shoot in our constructs once (takes approximately 2 weeks for the algae to grow and can be assayed on plate). To ensure we could obtain all the information from a single transformation we designed the experiment with the appropriate controls: negative control was biolistic transformation with water, positive control was transformation with verified backbones from Saul Purton algal biotechnology lab at UCL which contains the same homology regions are our constructs.
For each plasmid, the biolistics was done with 3 different concentrations of plates:
A,B -- 1 million cells per plate
C,D - 10 million cells per plate
E,F - 70 million cells per plate
The following constructs were shot in:
Construct 1
5’ end homology region + psaA 5’ UTR promoter + aadA gene (conferring resistance to spectinomycin) + rbcL 3’ UTR terminator + 3’ end homology region
Construct 25’ end homology region + psaA 5’ UTR promoter + aphA6 gene (conferring resistance to kanamycin) + rbcL 3’ UTR terminator + 3’ end homology region
Having developed the parts library for Chlamydomonas reinhardtii and proved the concept of the biobricks standard syntax which allows for the regulated assembly into composite devices we investigating putting this under trial of real-life conditions to transform Chlamydomonas reinhardtii chloroplasts through biolistics. Please read more about the demonstration of the DIY biolistic gene gun we have developed in the lab this summer. Taking advantage of the aadA resistance gene which we were able to verify in E. coli colonies, we constructed this Phytobrick with a 5’ UTR psaA promoter and a rbcL 3’ UTR terminator, each flanked by the homology regions for insertion into the trnE2-psbH intergenic region (shown to yield high expression rates of the transgene).
Having developed the parts library for Chlamydomonas reinhardtii and proved the concept of the biobricks standard syntax which allows for the regulated assembly into composite devices we investigating putting this under trial of real-life conditions to transform Chlamydomonas reinhardtii chloroplasts through biolistics. Please read more about the demonstration of the DIY biolistic gene gun we have developed in the lab this summer. Taking advantage of the aadA resistance gene which we were able to verify in E. coli colonies, we constructed this Phytobrick with a 5’ UTR psaA promoter and a rbcL 3’ UTR terminator, each flanked by the homology regions for insertion into the trnE2-psbH intergenic region (shown to yield high expression rates of the transgene).
Cas9 Modelling
We managed to write a code that would enable anyone to predict the time taken to achieve homoplasmy using the appropriate model for Cas9 activity. This program is also designed to be flexible in the sense that various input parameters can be changed to fit the parameters of your experiment. For more information, please read a complete documentation of the program under the 'Modeling' page.
