Difference between revisions of "Team:Tianjin/Note/Protein Engineering"

Line 31: Line 31:
  
 
<!------------------------------------------------------------------------------------------------------------------------------>
 
<!------------------------------------------------------------------------------------------------------------------------------>
−
<script type="text/javascript" src="http://malsup.github.com/jquery.media.js"></script>
+
 
 
<script type="text/javascript">
 
<script type="text/javascript">
 
wd = $(document.body).width() * 0.84;
 
wd = $(document.body).width() * 0.84;
Line 344: Line 344:
 
</script>
 
</script>
 
</html>
 
</html>
−
 
+
{{:Team:Tianjin/Templates/AddJS|:Team:Tianjin/js/material/mediaplayer}}
 
{{:Team:Tianjin/Templates/AddJS|:Team:Tianjin/Attribution/js/camarts.js}}
 
{{:Team:Tianjin/Templates/AddJS|:Team:Tianjin/Attribution/js/camarts.js}}
 
{{:Team:Tianjin/Templates/Sponsor|}}
 
{{:Team:Tianjin/Templates/Sponsor|}}

Revision as of 09:56, 17 October 2016

TEAM TIANJIN

LOGO


Team Tianjin-Attribution

Notes For Protein Engineering

Section 1

  • PCR (Q5 DNA Polymerase Protocol) was applied to amplify single stranded DNA of site mutation for overlap in next step, 48 wells on plate was used. Gel electrophoresis implied that N205L_Reverse, S92A_Reverse, Q119A_Forward, Q199A_Reverse, S207T_Forward and M154A_Reverse were not properly amplified. After several trials and errors, annealing temperature was slightly reduced. Forward and reverse single stranded DNA of all 24 mutation sites were properly prepared.

  • All PCR product was purified (DNA Purification Protocol).

  • Overlapping forward and reverse single stranded DNA of all 24 mutation sites (Q5 DNA Polymerase Protocol). Considering several sites had bad gel electrophoresis results, touchdown PCR was introduced. We set the annealing temperature varying from 62 degrees centigrade to 55 degrees centigrade, which meant temperature would touch down 0.2 degrees centigrade every cycle in 35 PCR cycles.

  • After several trials and errors, optimized condition was found. All mutation sites PCR product were inspected through gel electrophoresis. Sites W159H, W159A, R90T, R90I, R90A, S92A, S207A were discarded for their bad stripe images implied the original primer might had been degraded due to exposed to relatively high temperature (our laboratory room temperature could occasionally rise to above 30 degrees centigrade). These sites were prepared again later.

  • Genome was extracted from Saccharomyces cerevisiae, and was used as template to prepare alpha-factor signal peptide. PCR was firstly applied with Q5 DNA Polymerase Protocol as annealing temperature was 65 degrees centigrade. Gel electrophoresis implied that alpha-factor signal peptide was not properly prepared. The second time we used Pfu DNA Polymerase Protocol and annealing temperature was set to 50 degrees centigrade. Gel electrophoresis implied alpha-factor signal peptide was properly prepared. Product was purified (DNA Purification Protocol).

    • Show More

    Section 2

  • Help Cell-Free team prepare site mutation DNA segments. Q5 DNA Polymerase Protocol and Pfu Polymerase Protocol were both applied. To attain the best quality PCR product, more than 8 times PCR was performed on 96-wells plates, each time more than 20 wells were used. Touchdown PCR was also introduced.

  • Help Consortia team perform PCR on pBBR plasmid.

  • PCR (Pfu DNA Polymerase Protocol) was applied to prepare CYC1 terminator and was extracted from gel (Gel DNA Purification Protocol).

  • PCR (Pfu DNA Polymerase Protocol) was applied to prepare PGK promoter and was extracted from gel (Gel DNA Purification Protocol). After several trials and errors we found the rational condition to prepare PGK promoter gene.

  • Colony PCR was applied to help Consortia team verify genes on E.Coli genome.

  • Plasmid pRS416 was performed PCR with primers of alpha-factor signal peptide to check whether pRS416 was correctly linked with alpha-factor signal peptide. Result was negative, one hypothetical explanation was our plasmid donated by other laboratory fellows might have been damaged after a long period (at least 2 years) storage in fridge. We decide to substitute pRS415 for pRS416.

  • Help Consortia team perform PCR to prepare several genes.

    • Show More

    Section 3

  • PCR (Q5 DNA Polymerase Protocol) was applied to amplify PETase wild type gene, for future use.

  • We tried to combine all components including PGK promoter, CYC1 terminator, PETase mutant gene as well as alpha-factor signal peptide on plasmid pUC19. We tried to apply DNA Ligase Protocol to all 4 components simultaneously but found the efficiency was rather low. After several trials and errors we successfully prepared recombinant plasmid though it took several days.

  • We tried to link PETase mutant I208V gene to plasmid pRS415, and check whether it was successful use the same method described before. Gel electrophoresis confirmed that pRS415 was correctly linked with PETase mutant I208V gene. We also noticed that there exist 2 EcoRI cutting sites on pRS416 (one on resistance gene), which led to the failure in last week.

    • Show More

    Detailed Notes

    Detailed Notes
    Show More
    info_outline
    Notice: This page is currently under construction. Contents in this page are temporaory and will be modified several times before the final release.     — 2016 iGEM Team Tianjin
    Team Tianjin Sponsor Alltech
    Team Tianjin Sponsor GenScript
    Team Tianjin Sponsor SynbioTech