Difference between revisions of "Team:BIT-China/Design"

Revision as of 02:16, 19 October 2016

What is the problem?

Plasmid segragational instability has been the limit step for large-scale protein production and bioremediation. Antibiotic abuse or Stress Conditions for plasmid retention is not practical in this situation.

High copy number (HCN) plasmids are lost from population at a high rate due to the large metabolic burden and lack of nature factors for plasmid maintenance.

Our P-SLACKiller

IDEA

Equip the bacteria with a plasmid-sensing logically adjustable cell killer (P-SLACKiller), we need to select a signal which can indicate the intracellular plasmid numbers. There is a basic rule: when the plasmid numbers are above the threshold, we regard it as a normally-working bacterium and the P-SLACKiller won't start; however, when the plasmid numbers are below the threshold, we judge it as a slacker and the P-SLACKiller will kill these slackers, so that we can achieve the goal of stabling the number of plasmid. In the end, we selected the inhibitor protein as the signal molecular and the "in-promoter" as a switch to start the killer gene in order to control the plasmid numbers.

PART DESIGN

The basic circuit is shown in Fig.1.

Fig.1 The basic circuit of P-SLACKiller.

We use the constitutive promoter to express the inhibitor protein, thus the intracellular inhibitor concentration is positively correlated with the plasmid numbers. The inhibitor can repress the "in-promoter" and control the expression of downstream killer gene. To avoid the unexpected influence on killer gene caused by the constitutive promoter, we designed the gene circuit with the constitutive promoter and the "in-promoter" which express along different directions. When the signal of plasmid losing is detected, that is, the inhibitor concentration decreases, the executor killer will play a role.

The genetic locus of functional gene can be substituted on the basis of production demand in the future.

INSIDE MECHANISM

Under normal circumstance, for the constitutive promoter, the plasmid numbers are above the threshold, the inhibitor concentration is high enough to completely repress the activity of "in-promoter". Considering the effect of plasmids segregational stability, the concentration of plasmids will decline with time going on. When the plasmid numbers are below the threshold, the decrease of inhibitor proteins will lead to the increase of "in-promoter" activity. At this time, the killer gene will express and kill the cell. We define that, when the killer expressed is just able to kill the cell, the plasmid numbers is the threshold we've talked about. Based on this, we concluded that when the plasmid numbers are above the threshold, the bacteria can survive and have high working efficiency. This range is called survival range. To prevent the slackers consume a lot of nutrition, we kill it when the range comes to the dead one.

In this way, we can optimize the general population structure through plasmid-numbers-control.

Fig.2 With the decrease of plasmid numbers, the concentration of repressor will reduce to a threshold. According, "in-promoter" activity will rise up and star the transcription of killer gene.

Threshold device

The most critical factor in our system is the inhibitor concentration since it controls the switch of our killer system. Thus we need to prove that the "in-promoter" will have different responses corresponding to different concentrations of inhibitor.

We combined the wet experiment results and the mathematical model to measure the final result. [know more about our model]

First Step

Since it's hard to control the plasmid numbers, we employed the arabinose induced P_BAD promoter. The plasmid numbers is stable in short time. By adding different concentration of arabinose, we can simulate the production of inhibitors with different concentration. In this way, we can see the downstream "in-promoter" stay in the corresponding statues. rfp is used to replace the killer gene for simplifying our wet experiment. To expand the application of our system, we choose three combinations of inhibitor and "in-promoter".

Goal

(1) Build three parallel circuits employing different inhibitor proteins

(2) Find the relationship of the inhibitor and "in-promoter"

(3) Find out the initial thresholds by measuring RFP intensity

(4) Provide experimental data for modeling part

Part Design

The gene circuits are shown in Fig.3.

Fig.3 The gene circuits of threshold device.

(1) Part:BBa_K808000 AraC-P_BAD is used to control the expression of inhibitor proteins, The concentration of inducer arabinose is regarded as an input signal, and the red fluorescence intensity controlled by "in-promoter" is the output.

(2) Three combinations of inhibitor and "in-promoter" are selected to prove the concept of plasmid quorum sensing. Due to the limit of time, we measured 1-2 circuits. [see inhibitor mechanisms]

(3) rfp is used as an indicator since it's easier to quantify compare with the killer gene.

(4) The inducible promoter P_BAD and the "in-promoter" express towards different directions, a terminator B0015 is added between the two promoters.

We assume that:

Different concentrations of arabinose will induce inhibitor with different concentrations.

The high concentration of inducers can simulate high concentration of plasmids due to the same effect of producing more inhibitor proteins.

By adding different concentration of arabinose, we can measure the fluorescence intensity of RFP and find out the relationship of the arabinose and RFP intensity and the initial thresholds under control of certain inhibitor proteins.

Second step

In order to find out the concentrations of inhibitor under different concentrations of arabinose and use the results to derive the threshold of plasmids number in the constitutive circuit. Inhibitor is replaced by RFP and induced based on the same condition. The concentration of inhibitor can represented by measuring the fluorescence intensity of RFP.

Goal

(1)Represent the concentration of inhibitor by measuring the fluorescence intensity of RFP.

(2) Derive the threshold of plasmids number in the constitutive circuit

Part Design

The gene circuits are shown in Fig.4.

Fig.4 The gene circuit constructed to find out the concentrations of inhibitor induced by different concentrations of arabinose.

We assume that:

More arabinose added, more RFP expressed which can stand for the concentration of inhibitor, and vice versa.

Fig.5 The relationship between the concentrations of inhibitor and plasmid number.

Thus we could find out the relationship between the concentration of arabinose and inhibitor.

Third step

We use plasmids with different copy numbers to simulate the concentration of plasmids losing on different levels. Three kinds of plasmids, pSB1k3 (100~200 copies), pSB3k3 (20~30 copies), pSB4k5 (5~10 copies), are chosen and constructed with target fragment. By observing our system's working conditions, we can finally prove its function of controlling plasmids number.

Goal

(1) Simulate the plasmids losing on different levels

(2) Prove that our system is functional

Part Design

The gene circuits are shown in Fig.6.

Fig.6 The gene circuits of threshold device with constitutive promoter.

(1) We constructed the circuit on different plasmids with different copy numbers.
(2) The locus of constitutive promoter will be replaced by another constitutive promoter which has the similar strength as P_BAD promoter.

We assume that:

When the number of plasmids is less than N, inhibitor is not strong enough to inhibit the "in-promoter" totally, so the killer gene will express triggering the death of bacteria. On the contrary, if the number of plasmids is higher than N, the bacteria won't die.

We expect that in the high copy number plasmid circuit, fluorescence gene will express, and in the low copy number plasmid circuit, there will no fluorescence.

Forth step

The threshold of plasmid number is decided by the relationship between inhibitor and "in-promoter". To achievement the goal of build a controllable system, we decide to use different RBS (B0034 B0032) and promoters (J23119 J23116 J23109) with different strengths to change their concentrations. Thus we can finally change the threshold of plasmid as we hope.

Goal

(1) Adjust the threshold of plasmids by substituting different biobricks.

Part Design

The gene circuits are shown in Fig.7.

Fig.7 The gene circuits of threshold device constructed on a different plasmids with different copy numbers.

(1) Simulate the plasmids losing on different levels.
(2) The locus of B0034 and J23119 will be replaced by B0032 and J23109 J23116.

Killer device

As an executor for killing the cell labeled as slackers, killer device should include the detecting part like "in-promoter" interacting with inhibitor protein as well as the killing part like toxin gene mazF and hokD.

Ways of self-killing:

1) toxic protein

2) sgRNA targeting genome of strains with no NHEJ repair system

3) sgRNA targeting essential genes

PART DESIGN

At the first stage, we need to verify the function of two toxin proteins and make sure the bacteria can be killed after the expression of toxin proteins. To control the expression of killer gene, instead of J23119, arabinose inducible regulatory promoter/repressor unit [part number] is employed in our circuit.

Fig.8 Circuits for toxin gene function testing through induction by arabinose.

After measuring the growth curve, we observed the obvious difference between the testing group and control group. [see results page for killer]

To facilitate the measurement of plasmid threshold, we combined the inhibitor circuit with the killer circuit and replace the rfp for killer gene. [see design for threshold]

Fig.9 Circuits for testing for killing capacity under different concentration of arabinose, which can be regard as under different plasmid concentrations.

For the toxic protein, MazF and HokD were chosen as candidates. [see more about the killing mechanisms]

Upgraded P-SLACKiller

Why do we need to optimize our project?

It's possible to produce generation of plasmid-free cells, even if all plasmids were losen. Thus, we decided to integrate the killer device into genome to solve this problem. [see reombination]

To control the plasmid number above different thresholds, we need to adjust the initial threshold through replacement of RBS as well as "in-promoter" mutation. [see mutation]

Recombination

Recombineering ( recombination-mediated genetic engineering) is an efficient molecular engineering technique used for gene replacement, deletion and insertion.

Ways: a linear plus circular reaction

A：Employment of traditional λ-Red recombination

PART DESIGN

The basic circuit of upgraded P-SLACKiller is shown in Fig.10.

Compared with the original one, two homologous arms (50bp) are added. With the help of lambda Red recombination system, the killer part can be integrated into genome, preventing the whole system from being invalid. The final gene circuit is shown in Fig.11.

B: CRISPR-Cas9 coupling λ-Red recombineering

PART DESIGN

Difference between the two methods above: Traditional way use the resistance gene as a selection marker, while the CRISPR coupled way introduce a double-strand break (DSB) into the strain with no recombination occurred.

Application:

In our project, we tried both the two ways to test the integration efficiency. However, the CRISPR coupled way are deleted from our plan list due to the failure of cas9 and λ-Red plasmid construction.

We tried the traditional way with the pKD46 plasmid provided by Chun Li's lab and got the positive results. [results for recombination]

Two main factors will influence the recombination efficiency: the target site on genome and the length of homologous arms between donor fragment. [recombination protocol]

Promoter mutation

For inductive promoters, two kinds of region are significant to its transcription strength. One is common -10 and -35 region which can firmly bind to RNA polymerase, the other is operon region binding with regulatory factors like inhibitor proteins. [see mutation mechanisms]

Aim:

(1) To adjust threshold through changing "in-promoter's" strength
(2) Tied to specific promoter like P_Tet, build a mutants library and improve the existing part by measuring the strength through RFP

Part Design

After analyzing the promoter region of P_Tet, we designed random primers to mutate its -35 region. RFP intensity is measured to indicate the strength of mutated promoters. [see mutation results]

Design

Our P-SLACKiller
Threshold device
Killer device
Upgraded P-SLACKiller
Recombination
Promoter mutation

@@ Line 474: / Line 474: @@
                                  <img src="https://static.igem.org/mediawiki/2016/0/08/T--BIT-China--Project--Design--fig9.png"
                                       alt="fig9" class="center-block" style="width: 750px;">
-                         <div class="pic_info">Fig.9 Circuits for testing for killing capacity under different concentration of arabinose, which can be regard as under different plasmid concentrations. </div>
+                         <div class="pic_info"><b>Fig.9</b> Circuits for testing for killing capacity under different concentration of arabinose, which can be regard as under different plasmid concentrations. </div>
                              </div>
                              <div class="block-paragraph">